How To Program Bmw Key Fob E90 Bmw

  1. How To Program Bmw Key Fob E90 Bmw X1
  2. How To Program Bmw Key Fob E90 Bmw Key Fob
  3. How To Program Bmw Key Fob E90 Bmw 3 Series

There are two ways to program key for BMW if you use BMW OBD2 Multi-tool. Use file to program key directly off-line. 2 Programing key by OBD port online. Method 1:Off-line program bmw key. In this method,you do not need to connect BMW Multi-tool to car.But you need to read out the data file from CAS already. Programming a New Key from Scratch These instructions are for programming a new key when you do not have a working key fob. Insert key into the ignition and turn it to position 1 and back rapidly 5 times. Remove the key 3. Hold the unlock button and press the BMW. In this video I'm going to show you how to simply enable this little trick so you could start your BMW without inserted key.

┬╗Back To BMW Index

BMW 3-Series - Key Remote Programming

Three methods to try:

Method 1:

1. Working from within the vehicle and with the doors shut

2. Turn ignition to position 1 and back to off within 5 seconds.

3. Remove the key from ignition and press and hold the unlock button for 15seconds during this time press the key lock button 3 times within 5 seconds.

4. Release both buttons.

5. Doors will lock and unlock to show correct programming hasoccurred.

Method 2:

To do this procedure you need to have one working key and one key that needs tobe programmed.

1) Get in and close all doors.

2) Turn on the ignition and turn off quickly. (No more than 5 seconds) to startthe process. Next action must take place within 30 seconds.

3) Remove the 1st key.

4) Hold the key up near your left shoulder (this is so it is closer to the remotereceiver antenna.

5) Hold down the unlock button and press the lock button 3 times. Release theunlock button and the doors lock which confirms the operation.

6) Quickly repeat steps 4 & 5 for key #2 etc.

If it does not work, try doing the keys in opposite order. Key 2 then key 1, vs 1then 2.

Method 3:

Alternate if you do not have a working remote

1. Turn key to position 1 five times very quickly 2. Remove key 3. Hold unlockbutton then press lock button 3 times, release unlock button.

4. If you have another key do the same button pressing within 30 seconds 5. Turnon ignition to finalise.

PLEASE NOTE: This programming procedure programs the remote control part of thekey. Any transponder chip for the immobiliser (starting of car) will not be programmed and must be done by aspecialist.

┬╗Back To BMW Index

How To Program Bmw Key Fob E90 Bmw X1

BMW 3-Series - Key Remote Programming

Three methods to try:

Method 1:

1. Working from within the vehicle and with the doors shut

2. Turn ignition to position 1 and back to off within 5 seconds.

3. Remove the key from ignition and press and hold the unlock button for 15seconds during this time press the key lock button 3 times within 5 seconds.

Key

4. Release both buttons.

5. Doors will lock and unlock to show correct programming hasoccurred.

Method 2:

To do this procedure you need to have one working key and one key that needs tobe programmed.

1) Get in and close all doors.

2) Turn on the ignition and turn off quickly. (No more than 5 seconds) to startthe process. Next action must take place within 30 seconds.

3) Remove the 1st key.

How To Program Bmw Key Fob E90 Bmw Key Fob

4) Hold the key up near your left shoulder (this is so it is closer to the remotereceiver antenna.

5) Hold down the unlock button and press the lock button 3 times. Release theunlock button and the doors lock which confirms the operation.

How To Program Bmw Key Fob E90 Bmw 3 Series

6) Quickly repeat steps 4 & 5 for key #2 etc.

If it does not work, try doing the keys in opposite order. Key 2 then key 1, vs 1then 2.

Method 3:

Alternate if you do not have a working remote Can you download office 365 on a mac.

1. Turn key to position 1 five times very quickly 2. Remove key 3. Hold unlockbutton then press lock button 3 times, release unlock button.

4. If you have another key do the same button pressing within 30 seconds 5. Turnon ignition to finalise.

PLEASE NOTE: This programming procedure programs the remote control part of thekey. Any transponder chip for the immobiliser (starting of car) will not be programmed and must be done by aspecialist.