Washing Machine Caddy Error Codes

Is your Samsung washing machine displaying a fault code? Find out bellow what that Samsung washing machine error codes mean. These codes apply to both Samsung front loading washing machine and Samsung top loading washing machine.

Samsung Washing Machine 1E Error – Pressure Sensor Fault

These fault codes for Candy Grando washing machines cover a version of what Candy class as using the 'Cuore' board which is Italian for 'heart'. These washing machines and the Cuore board is used on washing machines produced in the Candy factory in Brugherio. The 'Cuore' Control Modules feature a potentiometer used for the program selector directly welded onto the printed circuit board. My Samsung Washing machine model WF1702WEA is indicating very frequent ‘SUD’ code and stop its washing cycle,by disconnecting the maims power plug and plugging it back, sometimes the machine will proceed the cycle. If your washing machine does not rotate the drum but displays the SE error, you need to check the control unit. In the event of a breakdown, it is not difficult to replace the unit. It is more complicated to repair the control board, solder the contacts and clean the tracks. A comprehensive list of Kenmore washer error codes. This quick guide will allow you to fix your washing machine without repairmen.

Description:

Samsung washing machine 1E error means that the washing machine has detected a fault with water level pressure sensor.

Action To Take:

1.Check wiring on pressure sensor and main PCB.

2. Replace pressure sensor.

Samsung Washing Machine 3E Error – Motor Fault

Description:

Samsung washing machine 3E error indicates that the machine is not detecting or is not able to rotate the wash motor. Machines that have motors with brushes the motor brushes are usually the first thing that should be checked. With newer inverter type motors start by checking the connections from PCB to the motor. Measure the resistance of the motor, this is best done straight on the plug from the main PCB. If the motor checks out ok and the resistance is even between points 1-3, 1-2 and 2-3 then the main PCB would be the cause for your Samsung washing machine 3E error.

Action To Take:

  1. Check that the drum can physically rotate and nothing is jamming it.
  2. Check wiring plugs on PCB and motor.
  3. If motor has carbon brushes, check them to make sure they are not worn out.
  4. Inverter type motor, measure resistance of windings, resistance between all 3 pins should be fairly even.
  5. If motor and wiring check out OK, replace main PCB.

Samsung Washing Machine 4E Error – Water Inlet Fault

Description:

Samsung washing machine 4E error indicates that the washing machine is not filling with water. 4E error could be caused by a simple thing like a tap that has been turned off. This is of the very common Samsung washing machine error codes. Lineage 2 clan crest gallery.

Action To Take:

1.Check that the tap is turned on, kinks in inlet hose and mesh filter on the inlet hose.

2.Check wiring and plugs on inlet valves and PCB.

3.Replace water inlet valve.

Samsung Washing Machine SE Error – Drain Fault

Description:

Samsung washing machine SE error means that the machine was not able to drain the water in the programmed time. This is also one of the very common Samsung washing machine error codes. This error can be caused by a blocked pump or filter, blocked or squished drain hose or a faulty drain pump. By checking the drain pump filter regularly the chances of this error are highly reduced and can prevent premature failure of the drain pump.

Here is a great video on how to clean the drain pump filter in Samsung front loading washing machine.

Action To Take:

1. Check drain pump filter and drain pump impeller for blockages and obstruction.

2. Check hoses for kinks and blockages.

3. Check that the house drain is not blocked.

4. Replace drain pump.

Samsung Washing Machine dE Error – Door Lock Fault

Description:

Washing

Washing machine is not able to lock the door to start a cycle.

Action To Take:

1.Make sure door is shut firmly.

2.Check plug and wiring on door lock and PCB.

3.Replace door lock.

4.Replace main PCB.

Samsung Washing Machine UE Error – Out Of Balance

Washing Machine Caddy Error Codes Download

Description:

Samsung washing machine UE error is an out of balance fault. This happens when the washing bunches up into one pile, can also be caused by a really small load that can not be distributed around the drum evenly or a stretched belt that is slipping and making the machine think that it is going out of balance.

Washing

Action To Take:

  1. Check load size, make sure its not too small.
  2. If clothes are bunched into a ball, break them up and try the spin cycle again.
  3. If error keep occurring, inspect the drum belt for wear.

Hope these Samsung washing machine error codes helped you with the repair.

Samsung Washing Machine Diagnostics Mode

Samsung washing machines have a diagnostics mode that can be entered by pressing a special sequence of buttons, different models have different ways of activation of the diagnostics mode. On our YouTube channel we show how to enter the diagnostics menu.

WW11K84120W – Click here for video.

Kenmore appliances are rather reliable and long lasting. However, even if a brand enjoys a reputation for quality, it still can give you some problems. If something goes wrong, our list of Kenmore washer error codes will be of great help to you. Most likely, you will have your machine back to work in a very short time.
It is important to understand, that in addition to basic Kenmore washer error codes, that work for all the appliances by this brand, there are also a number of fault codes, specific to certain models:
1. Kenmore Elite washer error codes give you a chance to diagnose the problem with any washing machine from the Kenmore Elite range.
2. Kenmore front load washer error codes listed below include both the most common and comparatively rare fault codes.
3. The list for Kenmore Elite Oasis washer error codes explains what the error codes that you see mean and offer the solutions to fix them yourself.
Communication of failure codes will be displayed on the washer console by all cycle lights flashing and standing status lights.
Kenmore basic washer error codes
Kenmore Duet washer error codes
Kenmore Oasis HE 110.2706, Oasis HE 110.2707, Oasis HE 110.2708, Oasis HE 110.2709 washer error codes
Kenmore 110.4646, 110.4647 washer error codes
Kenmore Automatic washers with Calypso error codes

Kenmore basic washer error codes

DISPLAYEXPLANATIONRECOMMENDED PROCEDURE
F01EEPROM ERROR
A communication error between the Central Control Unit (CCU)
and the EEPROM onboard the CCU occurred.
Possible Causes/Procedure
A power glitch may cause this error.
– Unplug washer or disconnect power for two minutes.
– Verify CCU operation by running a Diagnostic Test or any cycle.
PUMP DRIVE ERROR
The pump driver fails to activate
Possible Causes/Procedure
Replace CCU board
MAIN RELAYS ERROR
One of the main relays is not working properly
Possible Causes/Procedure
The relay might be soldered or always open.
– Replace CCU board
F11 (error solution F11)MOTOR CONTROL UNIT ERROR
The Motor Control Unit has internal failure; repeating under or
over voltage, or over current conditions. If failure occurs during
high-speed spin the door unlocks after 3 minutes
Possible Causes/Procedure
1. Unplug washer or disconnect power.
2. Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). Check the motor and do a continuity test.
3. Plug in washer or reconnect power.
4. Check the MCU by looking for operations of the drive motor.
5. Check the drive motor for powered rotations.
6. Replace MCU board.
F20 (error solution F20)NO WATER DETECTED ENTERING MACHINE
OR PRESSURE SWITCH TRIP NOT DETECTED
The pressure switch is not tripped after 6 minutes
Possible Causes/Procedure
If there is no water in the unit:
– Make sure that both valves at the water source(s) are turned on all the way.
– Check for plugged or kinked inlet hoses or plugged screens in the inlet valves.
– Verify inlet valve operation.
If there is water in the unit:
– Verify drain pump operation.
– Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch.
1. Verify there is not a siphon problem.
2. Press PAUSE/CANCEL twice to clear the display. The machine will drain for 3 minutes before unlocking the door.
3. Unplug washer or disconnect power.
4. Verify wire harness connections to inlet valves, pressure switch, drain pump and Central Control Unit (CCU).
5. Check all hoses for possible leaks.
6. Plug in washer or reconnect power
7. Verify pressure switch operation.
8. Verify CCU operation by running a Diagnostic Test or any cycle.
F21 (error solution F21)LONG DRAIN
If the drain time exceeds 8 minutes the water valves turn off.
NOTES:
After 4 minutes the 'Sd' error will be displayed, then
4 minutes later the 'F/21' error code will be displayed.
Press PAUSE/CANCEL two times to clear the display.Possible Causes/Procedure
1. Unplug washer or disconnect power.
2. Check the water temperature sensor and connection to it.
3. Check resistance of heating element, if present on this
model. (abnormal = infinity)
Possible Causes/Procedure
1. Check the drain hose and make sure it is not plugged or kinked.
2. Unplug washer or disconnect power.
3. Check the electrical connections at the pump and make sure the pump is running.
4. Check the drain pump filter for foreign objects.
5. Plug in washer or reconnect power.
6. If the above does not correct the problem, go to step 7.
7. Unplug washer or disconnect power.
8. Replace the pump.
F22DOOR LOCK ERROR
After 6 failed attempts to lock the door
Possible Causes/Procedure
Door lock mechanism is broken or removed from door.
Door switch/lock unit failure.
1. Unplug washer or disconnect power.
2. Check door switch/lock unit.
3. Check the wire harness connections to the door switch/lock unit and Central Control Unit (CCU)
F23HEATER FAILURE
If the temperature increase during the first 40 minutes is less
than 86°F (30°C)
Possible Causes/Procedure
1. Unplug washer or disconnect power.
2. Check connection to water heater.
3. Check resistance of heating element, if present on this model. (abnormal = infinity)
4. Check the water temperature sensor and connection to it.
F24 (error solution F24)WATER TEMPERATURE SENSOR ERROR
If the water temperature sensor (NTC) value is out of range
(23°F to 217°F [-5°C to 103°C]) during the water-heating step
of the WASH cycle.
Possible Causes/Procedure
1. Unplug washer or disconnect power.
2. Check the water temperature sensor and connection to it.
3. Check resistance of heating element, if present on this model. (abnormal = infinity)
F25 (error solution F25)DRIVE MOTOR TACHOMETER ERROR
If the control is unable to properly detect motor speed, the
machine shuts down. If a failure occurs during high-speed spin,
the door unlocks after 3 minutes
Possible Causes/Procedure
1. Verify the shipping system including shipping bolts, spacers
and cables are removed.
2. Unplug washer or disconnect power.
3. Check wire harness connections between the drive motor
and the Motor Control Unit (MCU), and between the MCU
and the Central Control Unit (CCU).
4. Plug in washer or reconnect power.
5. Check the MCU by looking for operations of the drive motor.
6. Check the drive motor for powered rotations
F26DOOR SWITCH ERROR
If the door has not been opened for 3 consecutive cycles or the
door switch is open while the door is locked for more than
5 seconds
Possible Causes/Procedure
Door not opened during 3 consecutive cycles.
1. Open and close the door.
2. Verify CCU operation by running a Diagnostic Test or any
cycle.
Door switch open while door is locked.
1. Push the door and check if it is completely closed.
2. Verify CCU operation by running a Diagnostic Test or any
cycle
F27OVERFLOW CONDITION
If the overflow contact on the pressure switch is closed for
more than 60 seconds, an Overflow Condition occurs. In an
overflow condition, the door remains locked and the drain pump
runs constantly, even if PAUSE/CANCEL is pressed twice and
the display is cleared. Turn off hot and cold water faucets and
unplug the unit before servicing
Possible Causes/Procedure
1. Check the drain hose and make sure it is not plugged or
kinked.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the drain pump, pressure
switch, water inlet value, and Central Control Unit (CCU).
4. Check/clean drain pump filter of foreign objects.
5. Check for drain pump failure.
6. Check the inlet valve for proper shut off.
7. Check the pressure switch for proper operation
F28 (error solution F28)SERIAL COMMUNICATION ERROR
The communication between the Central Control Unit (CCU) and
the Motor Control Unit (MCU) cannot be sent correctly
Possible Causes/Procedure
1. Unplug washer or disconnect power.
2. Check wire harness connections to the MCU, the motor, and
Central Control Unit (CCU).
– Check connections of the CCU board within the housing.
– Make sure all grounding switches are engaged.
3. Check the drive system for any worn or failed components.
4. Plug in washer or reconnect power.
5. Verify CCU operation by running a Diagnostic Test or any
cycle.
6. Check the MCU by looking for operations of the drive motor.
7. Check the drive motor for powered rotations.
8. Check that the serial harness at the MCU is not mounted
upside down. The wires should be to the left when facing
the MCU connectors.
F29DOOR UNLOCK ERROR
If the door unlock has failed 6 times
Possible Causes/Procedure
Door lock mechanism is broken.
Door switch/lock unit failure.
1. Check door switch/lock unit for foreign objects.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the door switch/lock
unit and Central Control Unit (CCU).
NOTE: The door switch/lock unit can be manually unlocked.
F30 (error solution F30)DISPENSER SYSTEM ERROR
When the dispenser motor cannot be driven to its proper
position
Possible Causes/Procedure
1. Unplug washer or disconnect power.
2. Check mechanical linkage from dispenser motor to the top
of the dispenser.
3. Check wire harness connections to the dispenser motor
and Central Control Unit (CCU).
4. Check dispenser motor for powered rotations
F31MCU FAILURE
If the heat sink gets too hot, the Motor Control Unit (MCU) will
stop the motor, the MCU will communicate this failure to the
Central Control Unit (CCU), then the CCU will reset the MCU.
If the condition continues four times, the F31 code will show
Possible Causes/Procedure
1. Check for proper installation, verify the unit is not located
near a source of heat and has proper ventilation.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the MCU, the motor,
and Central Control Unit (CCU).
4. Check the drive system for any worn or failed components.
5. Plug in washer or reconnect power.
6. Check the MCU by looking for operations of the drive motor.
7. Check the drive motor for powered rotations
F33 (error solution F33)PUMP DRIVE SYSTEM ERROR
When the connection between pump and the Central Control
Unit (CCU) is lost
Possible Causes/Procedure
1. Unplug washer or disconnect power.
2. Check wire harness connections to the pump and Central
Control Unit (CCU).
3. Plug in washer or reconnect power.
4. Verify CCU operation by running a Diagnostic Test or any
cycle.
rLLOAD INSIDE DRUM DURING CLEANING
WASHER CYCLE
If at the start of the CLEANING WASHER cycle a load is
detected inside the drum.
NOTE: Detects by weight.
Possible Causes/Procedure
Remove clothes from drum and start the cycle again
SdSUDS LOCK (OVERDOSE OF DETERGENT
DETECTED DURING THE WASH CYCLE)
If suds are detected continuously by the pressure switch during the
drain or spin phases, the washer will fill 4 liters of water and during
5 minutes the unit will rest without tumbling, the water will be drained
and it will try to spin or drain again
Possible Causes/Procedure
If too much detergent was used:
– Run the unit through a RINSE/SPIN cycle.
– Run a NORMAL cycle without adding any detergent.
This should clear the unit of the excess detergent.
1. Check the drain hose and make sure it is not plugged or
kinked.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the drain pump, pressure
switch, and Central Control Unit (CCU).
4. Check/clean drain pump filter of foreign objects.
5. Plug in washer or reconnect power.
6. Check drain pump.
7. Check the pressure switch.
8. Verify CCU operation by running a Diagnostic Test or any
cycle.

Kenmore Duet washer error codes

Kenmore was founded in 1927. Today this brand sells a wide range of kitchen and laundry appliances than can be bought in stores belonging to Sears Holdings Corporation. The appliances are manufactured by several companies, including Whirlpool, Panasonic, LG, and Electrolux.
The first ever appliance sold by Kenmore was a washer. It appeared on the market in 1927. Today the brand’s lineup consists of most popular types of washing machines, including front-load and top-load ones. It is among the industry leaders. Many Kenmore washers are capable of doing laundry loads in less time than appliances produced by other brands.
Some models do not have the display to show the failure codes. They use the status lights on the touchpad/LED
Failure CodesDuet Sport Status LEDsDuet Sport Ht Status LEDs
F/01Add a GarmentAdd a Garment
F/11 (error solution F/11)Add a Garment, Wash,
Spin
Add a Garment,
Soak/Prewash, Rinse
F/20 (error solution F/20)Rinse, Cycle CompleteWash, Spin
F/21 (error solution F/21)Add a Garment, Rinse,
Cycle Complete
Add a Garment, Wash, Spin
F/22Wash, Rinse,
Cycle Complete
Soak/Prewash, Wash, Spin
F/23Add a Garment, Wash,
Rinse, Cycle Complete
Add a Garment,
Soak/Prewash, Wash, Spin
F24 (error solution F/24)Spin, Cycle CompleteRinse, Spin
F25 (error solution F/25)Add a Garment, Spin,
Cycle Complete
Add a Garment, Rinse, Spin
F/26Wash, Spin,
Cycle Complete
Soak/Prewash, Rinse, Spin
F/27Add a Garment, Wash,
Spin, Cycle Complete
Add a Garment,
Soak/Prewash, Rinse, Spin
F/28 (error solution F/28)Rinse, Spin,
Cycle Complete
Wash, Rinse, Spin
F/29Add a Garment, Rinse,
Spin, Cycle Complete
Add a Garment, Wash, Rinse,
Spin
F/30 (error solution F/30)Wash, Rinse, Spin,
Cycle Complete
Soak/Prewash, Wash, Rinse,
Spin
F/31Add a Garment, Wash,
Rinse, Spin,
Cycle Complete
Add a Garment,
Soak/Prewash, Wash, Rinse,
Spin
F/33 (error solution F/33)Add a GarmentAdd a Garment,
Cycle Complete
rLWashSoak/Prewash,
Cycle Complete

Kenmore Oasis HE 110.2706, Oasis HE 110.2707, Oasis HE 110.2708, Oasis HE 110.2709 washer error codes

Washing machines Kenmore Oasis HE 110.2706, Oasis HE 110.2707, Oasis HE 110.2708, Oasis HE 110.2709 are top-loading ones. These washers are provided with such extremely useful options as “Save energy plus”, “2nd Rinse”, “Stain treat”, “Auto Soak/Prewash” and, of course, “Cycle signal volume”.

Washing Machine Caddy Error Codes For Windows 10

CODESSOLUTION
LF (error solution LF) (Washer is taking too long to fill)Check the following:
Are the water inlet hoses kinked or clogged?
Are the water inlet valve screens clear?
Press STOP to clear display.
Ld (error solution Ld) (Washer is taking too long to drain water from the wash tub)
'uL' (Unbalanced Load)If the load is unbalanced, the washer will display this code while running an imbalanced load correction routine at the end of the wash cycle and before the final spin. If the code remains and the wash cycle dial is flashing after the recovery routine has stopped, open lid and redistribute the load. Close lid and press START.
'oL' (Over Load)Is the washer overloaded? The washer has attempted to fill and begin the wash cycle. If the washer is overloaded, it will drain any water and detergent that was added during the fill. To correct the overload, remove several items and add detergent. Close lid and press START.
'Sd' (Suds Detected)Did you use regular detergent?
Regular or hand-washing detergents are not recommended for this washer. Use only High Efficiency ('HE') detergent.
Did you add too much detergent?
Always measure detergent. Follow detergent manufacturer's directions.
If excessive suds are detected, the washer will display this code while running a suds reduction correction routine at the end of the wash cycle. The suds reduction routine removes extra suds and assures proper rinsing of your garments. If the code remains and the wash cycle dial is flashing after the recovery routine has stopped, re-select your desired cycle using cold water. Press START. Do not add detergent.
'lid' (Lid Opened)This code will appear at the end of the wash cycle to indicate that the cold and hot water inlet hoses are switched.
'dL' (Door/Lid cannot lock)Indicates lid is not locked. Check for items caught in the lid keeping it from closing. Press STOP once to clear the code.
'dU' (Door/Lid cannot unlock)Is there excessive weight on the lid, such as a basket of laundry? Excessive weight will keep the lid from unlocking. Press STOP once to clear the code.
'F##' codePress STOP once to clear code. Press START. If code appears again, call for service.

Kenmore 110.4646, 110.4647 washer error codes

Washing machines Kenmore 110.4646, 110.4647 are front-load washers. They are designed to use only HE High Efficiency Detergents. However, they represent the optimal ratio of price-quality.

CODESSOLUTION
'Rinse' and 'Clothes Clean' Status Light illuminated or F20 (error solution F20) on display (on some models) (Water Inlet Problem ─ no water or insufficient water supply)Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
Check the following:
Are water faucets completely turned on?
Are screens at inlet hose connection to washer clogged? Are water inlet hoses kinked?
Are water inlet hoses frozen?
Plug in washer or reconnect power, Re-select cycle and press START. If the problem remains, call for service.
'Add a Garment' 'Rinse' and 'Clothes Clean' Status Lights illuminated or F21 (error solution F21) on display (on some models) (Drain Problem)Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
Check the following:
Is the drain hose kinked?
Is the drain hose frozen?
Is the drain hose clogged?
Is the drain hose more than 96' (2.4 m) above the floor?
Any other Status light combination (Electrical Problem)
Select PAUSE/CANCEL twice to cancel the cycle. Select DRAIN & SPIN if there is excessive water in the washer.
Re-select cycle and press START. If the problem remains, call for service.

Washing Machine Caddy Error Codes List


Washing Machine Caddy Error Codes Free

Kenmore Automatic washers with Calypso error codes

Kenmore Automatic washers with Calypso belong to the elite kind of washing machines. They are created to use high efficiency detergent. These are top-loaded washers. They are designed, produced and tested to assure many years of fault-free performance.

Washing Machine Caddy Error Codes 2017

CODESSOLUTION
'PF' (Power Failure) flashesWas the washing cycle interrupted by a power failure? Press START to continue the cycle from the moment that power was lost, - OR - Press STOP/CANCEL to clear the display and completely cancel the cycle.
'FL' (Over Fill} flashesWas the washing cycle interrupted by a power failure? Press START to continue the cycle from the moment that power was lost, - OR - Press STOP/CANCEL to clear the display and completely cancel the cycle.
'Er' (Processor Reset Error)Cycle information was not stored during a power failure. Press STOP/CANCEL to clear the display.
Lf (error solution Lf) (Long Fill} flashesAre the water inlet hoses kinked or clogged? Are the water inlet valve screens clear? Press STOP/CANCEL to clear the display.
'CE' (Communications Error) flashes - beeps oncePress STOP/CANCEL to clear the display.
Ld (error solution Ld) (Long Drain) flashesIs the drain hose kinked or clogged? Press STOP/CANCEL to clear the display.
'CA' or 'CI' (Current Limit)Is the washer overloaded? Press STOP/CANCEL to clear the display.
'Or' (Open Relay)Washer operation failure. Call for service
'Sr' (Stuck Relay)Washer operation failure. Call for service
'LS' (Lid Switch Error) flashesIs the washer lid open? Close the lid and press START to continue the cycle.
Is the lid closed? Open and close the lid. Press STOP/CANCEL to clear the display.
'SU' (Suds Lock)Press STOP/CANCEL to clear the display. Drain/Spin load: restart cycle, De net add detergent. Use cold water
'dt' (Diagnostic Tests}For service diagnostics only. Press STOP/CANCEL to clear the display.
ob (error solution ob) (Off Balance)Is the load unbalanced? Redistribute the load. Close lid and press START.